10 Tell-Tale Signs You Must See To Buy A Fiat Panda Key Fob Replacement
Reasons Your Fiat 500 Key Fob Won't Work
A key fob for the Fiat 500 makes it simple to open doors and start your car. There are many reasons the fob won't work. It could be due to a dead battery damaged receiver module, water damage issues, and interference.
This listing is for a NEW replacement Fiat Flip Key Remote that is similar to the Ilco brand. It must be professionally programmed (click here to search for local locksmiths in the automotive industry). This remote includes lock, unlock and trunk buttons.
Dead Coin Battery
The most common reason your 500 key fob doesn't function is due to a dead battery. Modern key fobs come with a restricted operating range, and should be within a few feet of the vehicle to function. If you are not within your vehicle and you hit the keyfob, it will not respond and display the message "Key Fob Not Detected".
If this happens then replace the battery for your coin-cell (Part Number CR2032) by a brand new one of a reliable brand, like Panasonic Duracell or Energizer. discover here can be found in your local hardware store, or online.
You can test the battery of your coin-cell by pressing the buttons while standing close to your Fiat 500. The parking lights should flash and the key fob should operate the lock and unlock switch.
If the fob's key doesn't function after replacing the battery, it could have water damage that prevents it from communicating with the receiver module inside your vehicle. Water damage can happen in a number of ways, ranging from small splashes to submerging your fob in salt water at the beach. If you suspect your fob has been exposed to water, you can try placing it in a dry rice bag to pull the moisture back out. If this doesn't work your fob may require reprogramming by an experienced locksmith or dealer.
Water Damage
Water damage can happen if you immerse the fob into the ocean, or wash it in a washing machine. Saltwater poses a particular risk to the circuit board of the fob and can cause it to short out and eventually die. In the event that you let your fob get wet, it's not a good idea, but if you drop it in the water in a cup or fail to remove it from your pants pocket before running the washer Don't give up hope.
First, remove the battery. Clean the electronic chip using isopropyl alcohol or a similar product and then dry it thoroughly before replacing the battery. Next check the fob to verify if it is working. If the key doesn't function, it may need to be changed. This is usually done by an auto locksmith or dealer.
If the key you have is older and not programmed for your car it is necessary to replace it completely. A professional locksmith for automotive will be able to complete this process. The locksmith will need to cut the key to match the ignition of your car. They'll also have to reprogram the fob in the car's system. This is a quick and cost-effective process that can be completed in the next day.
Receiver Module Issues
The 500 key fob could not function because it's out of range. The remote has a range of 30 feet. So should you be too far away from your vehicle it won't be able to respond to your commands. It is possible to solve this problem by moving the remote closer to your car until it responds.
If you've replaced your coin battery (commonly known as a "button" or "watch") and your fob doesn't function It could be because of an internal circuit board problem. In most cases, reprogramming the fob will solve the problem. The instructions are available for most vehicles on YouTube or in the owner's guide.
It is possible to replace the metal clips that hold the coin batteries in the correct position. If they lose tension, it can prevent your coin battery from sitting properly and cause your remote to malfunction.
In rare cases the fob can become out of alignment with your vehicle because of hardware or software issues. You can fix this issue by visiting your local auto-locksmith or dealer to reprogram your key fob. In some instances they might need to reinstall the software on your body control module, as well.
Interference
Interference can also cause the key fob to not receive or transmit signals. This is possible when the key fob is in proximity to a radio transmitter (cell phones, radar detectors) or another source of electromagnetic radiation. The key fob might not work because of a problem with the buttons or water damage, or damage to the internal chips.
If your key fob suddenly stopped working, or you have tried everything at home to resolve it (e.g. You might have a damaged 500 receiver module if you've tried replacing the battery, reprogramming it, or using an alternative key fob. The receiver module is located under the dash and receives the radio frequency signals from the key fob. It converts them into electronic commands that the vehicle interprets.
There's a simple method to reset the 500's onboard system, including the keyfob. Disconnect the battery of 12 volts for about 15 minutes, by removing the negative cable first then the positive cable. Then, reconnect the battery. This will eliminate any residual electricity and restart the car's computers, which can help get your key fob working again. If the issue persists you should speak with an expert certified technician. They will be able to determine the exact cause of your issues.